Propellerhead Reason Spécifications télécharger pdf (Page 214)

BV512 VOCODER

212

10. Route MIDI to the carrier device by clicking in the MIDI symbol col-

umn for its track in the sequencer.

11. Play a chord or a note on your MIDI keyboard.

What you hear now is the vocoded sound, e.g. the carrier sound processed

to have the same tonal characteristics as the modulator.

12. Try the different filter band options and note the difference in

sound.

13. You can also adjust the vocoder sound by clicking and dragging the

bars in the lower display.

Each bar corresponds to a frequency band, with low frequencies to the left

and high frequencies to the right. You adjust the level of a band by dragging

its bar up or down. Clicking and dragging across the bars allow you to

change the levels of several bars, much like drawing an eq curve.

The upper display shows the spectrum of the modulator signal, for display only.

D To reset a band to ±0 dB, press [Command] (Mac) or [Ctrl] (Win)

and click on it.

You can also reset all bands to zero by bringing up the context menu for the

Vocoder device and selecting “Reset Band Levels”.

14. If the vocoder sound is “muddy” or indistinct, try raising the “HF

Emph” knob on the Vocoder.

This parameter (High Frequency Emphasis) boosts the high frequencies in

the carrier signal.

15. Try out the other parameters if you like.

See page 214 for details.

That’s it - a basic vocoder setup!

Vocoded vocals

The most common usage for a vocoder is probably the typical “singing” or “talk-

ing synth” sound, using vocals or speech as modulator. Since Reason doesn’t

support live audio input you cannot sing and play in real time - instead you need

to use sampled speech or vocals (with e.g. an NN-19 or NN-XT as the modulator

device). The procedure for this is roughly the same as in the tutorial above, but

this time you need to record or enter some notes in the sequencer for the mod-

ulator device (since the samplers don’t have pattern or Preview playback).

Here’s a quick guideline:

1. Create the carrier device.

2. Select the carrier device and create a BV512 vocoder.

3. Select the BV512 and create the modulator device (typically an NN-

19 or NN-XT sampler device).

4. Load the vocals or speech samples into the sampler device and as-

sign them to keyzones as desired.

For details about using sampler devices, see the respective device chapter.

5. Record or enter some notes on the sequencer track for the sampler

device, so that the vocal samples are played back where you want

them in the song.

To hear the unprocessed sound of the sampler device, set the Dry/Wet con-

trol on the BV512 to “Dry”, as above. When you’re done, turn the control

back to “Wet” to get the vocoded sound.

6. Route MIDI to the carrier device.

7. Start sequencer playback and play notes or chords on your MIDI

keyboard.

The result will be the classic vocoded vocal sound.

8. At this point you may want to record the notes or chords you play

for the carrier device.

As MIDI is already routed to the carrier device track, all you need to do is

start recording and play along.

1 2 ... 209 210 211 212 213 214 215 216 217 218 219 ... 297 298

Commentaires sur ces manuels

Vikitvv 04 Jan 2024 | 13:04:50

urenrjrjkvnm

Evabhf 07 Jan 2024 | 16:01:45

Med

Viktoridbv 14 Jan 2024 | 00:33:23

Cinema

Propellerhead Reason Spécifications Page 214

Commentaires sur ces manuels

Produits connexes et manuels pour Logiciel Propellerhead Reason